Products
VBOX CAN Gateway (CGW01)
CGW01
●Log vehicle CAN or CAN FD data in a VBOX system where secondary CAN modules are used
●Converts up to 32 CAN or CAN FD messages
●125 Kbit/s, 250 Kbit/s, 500 Kbit/s and 1 Mbit/s CAN rates
●Isolates VBOX data from the vehicle CAN bus
Overview
The VBOX CAN Gateway (CGW01) controls the flow of CAN data between two separate buses. It allows vehicle CAN or CAN FD bus data to be logged by a VBOX system while secondary CAN modules, such as the Mini Input Module, communicate with the VBOX at the same time.
Normally, capturing CAN data from a car together with data from a module would put VBOX and module data onto the vehicle CAN bus, with unpredictable and almost certainly unwanted results. The CAN Gateway lets the VBOX log both data streams without any module traffic going back onto the vehicle bus.
Connected to a PC with the supplied RLCAB117 USB cable, it can be programmed with dedicated setup software to read almost any CAN message format and re-transmit it onto the VBOX CAN bus.
Uses
VBOX 3i, VBOX 4 and VBOX 3iS owners, as well as non-Racelogic users, can use the CAN Gateway to:
●Convert up to 32 CAN FD messages to CAN and output them on a different CAN bus
●Isolate 2 CAN buses while allowing all messages to be transferred to a different CAN bus
●Convert data from one CAN bus speed to another
●Filter data from one CAN bus and forward specific data to another CAN bus
Technical Specifications
CAN
●Type: CAN 2.0A, CAN 2.0B, Flexible Data Rate (CAN FD)
●CAN baud rates: 125 Kbit/s, 250 Kbit/s, 500 Kbit/s or 1 Mbit/s
Environmental
●Operating temperature: -20°C to +70°C
●Storage temperature: -40°C to +85°C
Power
●Input voltage: 4.5–30 V DC
●Power: 0.6 W
Physical
●Dimensions (L x W x H): 90.8 x 57.13 x 26.13 mm
●Weight: 110 g
●Protection rating: IP51
The VBOX CAN Gateway (CGW01) controls the flow of CAN data between two separate buses. It allows vehicle CAN or CAN FD bus data to be logged by a VBOX system while secondary CAN modules, such as the Mini Input Module, communicate with the VBOX at the same time.
Normally, capturing CAN data from a car together with data from a module would put VBOX and module data onto the vehicle CAN bus, with unpredictable and almost certainly unwanted results. The CAN Gateway lets the VBOX log both data streams without any module traffic going back onto the vehicle bus.
Connected to a PC with the supplied RLCAB117 USB cable, it can be programmed with dedicated setup software to read almost any CAN message format and re-transmit it onto the VBOX CAN bus.
Uses
VBOX 3i, VBOX 4 and VBOX 3iS owners, as well as non-Racelogic users, can use the CAN Gateway to:
●Convert up to 32 CAN FD messages to CAN and output them on a different CAN bus
●Isolate 2 CAN buses while allowing all messages to be transferred to a different CAN bus
●Convert data from one CAN bus speed to another
●Filter data from one CAN bus and forward specific data to another CAN bus
Technical Specifications
CAN
●Type: CAN 2.0A, CAN 2.0B, Flexible Data Rate (CAN FD)
●CAN baud rates: 125 Kbit/s, 250 Kbit/s, 500 Kbit/s or 1 Mbit/s
Environmental
●Operating temperature: -20°C to +70°C
●Storage temperature: -40°C to +85°C
Power
●Input voltage: 4.5–30 V DC
●Power: 0.6 W
Physical
●Dimensions (L x W x H): 90.8 x 57.13 x 26.13 mm
●Weight: 110 g
●Protection rating: IP51